Ford Escape Manuals
Ford Escape 2020-2023 Owners Manual / Maintenance / Changing the Engine Air Filter - 2.5L, Hybrid Electric Vehicle (HEV)/Plug-In Hybrid Electric Vehicle (PHEV). Changing the Fuel Filter - Gasoline, Hybrid Electric Vehicle (HEV)

Ford Escape: Maintenance / Changing the Engine Air Filter - 2.5L, Hybrid Electric Vehicle (HEV)/Plug-In Hybrid Electric Vehicle (PHEV). Changing the Fuel Filter - Gasoline, Hybrid Electric Vehicle (HEV)

Changing the Engine Air Filter - 2.5L, Hybrid Electric Vehicle (HEV)/Plug-In Hybrid Electric Vehicle (PHEV)

WARNING: To reduce the risk of vehicle damage and personal burn injuries, do not start your engine with the air cleaner removed and do not remove it while the engine is running.

When changing the air filter element, use only parts that meet or exceed our specifications.

Change the air filter element at the proper interval.

Note: If you do not use the correct air filter element, your vehicle warranty could be void.

Ford Escape. Hybrid Electric Vehicle (PHEV). Changing the Fuel Filter - Gasoline, Hybrid Electric Vehicle (HEV)

  1. Using a screwdriver, loosen the clamp on air filter housing cover.
  2. Gently pull the boot back away from the air filter housing cover.
  3. Release the two clips from the air filter housing cover.
  4. Remove air filter housing cover.
  5. Remove the air filter element from the air filter housing.
  6. Wipe any dirt or debris from the air filter housing assembly to make sure no dirt gets in the engine and to make sure you have a good seal.

    Ford Escape. Hybrid Electric Vehicle (PHEV). Changing the Fuel Filter - Gasoline, Hybrid Electric Vehicle (HEV)

  7. Install a new air filter element. Be careful not to crimp the filter element edges between the air filter housing and cover. This could cause filter damage and allow unfiltered air to enter the engine if it is not properly seated.
  8. Install the air filter housing cover.
  9. Engage the clips to secure the air filter housing cover to the air filter housing.
  10. Reconnect the boot to the air filter housing cover and tighten securely.

Changing the Fuel Filter - Gasoline, Hybrid Electric Vehicle (HEV)

Your vehicle has a lifetime fuel filter that integrates with the fuel tank. It does not need regular maintenance or replacement.

    Changing the Engine Air Filter - 1.5L EcoBoost™/2.0L EcoBoost™

    WARNING: To reduce the risk of vehicle damage and personal burn injuries, do not start your engine with the air cleaner removed and do not remove it while the engine is running...

    Drive Belt Routing Overview - 1.5L EcoBoost™ and 2.0L EcoBoost™

    1.5L EcoBoost™ 2.0L EcoBoost™ The long drive belt is on the first pulley groove closest to the engine. The short drive belt is on the second pulley groove farthest from engine...

    Other information:

    Ford Escape 2020-2023 Service Manual: General Procedures - Powertrain/Drivetrain Mount Neutralizing


    Adjustment All vehicles With the vehicle in NEUTRAL, position it on a hoist. Refer to: Jacking and Lifting - Overview (100-02 Jacking and Lifting, Description and Operation). Remove the fasteners and the undershield. 1...

    Ford Escape 2020-2023 Service Manual: Removal and Installation - Passenger Door Module (PDM)


    Removal NOTE: Removal steps in this procedure may contain installation details. NOTE: Drivers side shown, passenger side similar. NOTE: If installing a new module, it is necessary to upload the module configuration information to the diagnostic scan tool prior to removing the module...

    Categories

    Master Access Code

    What Is the Master Access Code

    The master access code is a factory-set five-digit entry code. You can operate the keypad with the master access code at any time. The master access code is on the owner’s wallet card in the glove box and is available from an authorized dealer.

    Displaying the Master Access Code

    To display the factory-set code in the information display:

    Ford Escape. Master Access Code

    Remove the rubber mat. Insert the first programmed key in the backup slot. Press the push button ignition switch once and wait a few seconds. Press the push button ignition switch again and remove the key. Within 10 seconds, place a second programmed intelligent access key in the backup slot and press the push button ignition switch.

    read more

    Copyright © 2023 www.fordescape4.com