Ford Escape Manuals
Ford Escape 2020-2024 Service Manual / Chassis / Brake System / Brake System - General Information / General Procedures - Brake Service Mode Activation and Deactivation

Ford Escape: Brake System - General Information / General Procedures - Brake Service Mode Activation and Deactivation

Activation

  WARNING: Service actions on vehicles equipped with electronic parking brakes may cause unexpected parking brake application, which could result in injury to hands or fingers. Put the electronic parking brake system into service mode prior to servicing or removing rear brake components. Failure to follow this instruction may result in serious personal injury.

  WARNING: Service actions on vehicles equipped with electronic brake booster without activating the brake system service mode may result in unexpected hydraulic brake application or a false leak detection DTC. This will significantly reduce the performance of the brake system. Failure to follow this instruction may result in serious personal injury.

NOTE: Brake service mode is also known as brake maintenance mode.

NOTE: Prior to carrying out the brake service mode activation steps below, clear all EPB and EBB related DTC's.

NOTE: Carry out the following service mode activation procedure to deactivate the EPB and EBB systems. The EPB and EBB system can also be deactivated using the diagnostic scan tool and following the on-screen instructions.

NOTE: This mode is required to deactivate the brake boost and to allow the entire brake system to be bleed manually.

NOTE: This mode will cause all the associated brake warning indicators and text messages to appear.

  1. Set the ignition to ON.
  1. Release the EPB .
  1. Press and hold the accelerator pedal and place the EPB switch to the RELEASE (downward) position. Continue to hold the accelerator pedal and EPB switch.
  1. Set the ignition to OFF then set the ignition to ON within 5 seconds. Continue to hold the accelerator pedal and the EPB switch.
  1. Set the ignition to OFF then release the accelerator pedal and EPB switch.
    • NOTE: The brake system will be deactivated, preventing brake application until service has been completed and service mode has been deactivated. The yellow EPB indicator will be illuminated and Maintenance Mode will display on the message center.

    • NOTE: When replacing brake pads in service mode, the brake caliper piston must be compressed into the caliper housing. The brake caliper piston does not have to be rotated while compressing the piston.

Deactivation

NOTICE: The brake system performance will be significantly reduced when the brake system is put in service mode.

NOTE: Carry out the following Brake Maintenance Mode deactivation procedure to activate the EBB and EPB systems. These systems can also be activated using the diagnostic scan tool and following the on-screen instructions.

  1. Set the ignition to ON.
  1. Press and hold the accelerator pedal.
  1. Place the EPB switch in the APPLY (upward) position. Continue to hold the accelerator pedal and the EPB switch.
  1. Firmly press the brake pedal for at least 1 second. Release the brake pedal while continuing to hold the accelerator pedal and the EPB switch.
  1. Set the ignition to OFF then set the ignition to ON within 5 seconds, then release the accelerator pedal and the EPB switch.
    • NOTE: Once the ignition is set to ON, the EPB system will immediately apply and release the parking brake to guarantee sufficient air gap between the rear brake pads and brake disc. If the EPB switch is not released prior to completion of this sequence, it will apply the EPB . The EPB will have to released prior to moving the vehicle.

    • NOTE: When Brake Maintenance Mode is deactivated, the Yellow Parking Brake and Red Brake Warning Indicators turn off and "Brake Maintenance Mode" no longer displays in the message center.

    General Procedures - Brake Disc Machining

    Repair   WARNING: Service actions on vehicles equipped with electronic parking brakes may cause unexpected parking brake application, which could result in injury to hands or fingers...

    General Procedures - Brake System Draining and Filling - Vehicles With: Vacuum Brake Booster

    Special Tool(s) / General Equipment Fluid Container Draining Refer to: Brake and Clutch Systems Health and Safety Precautions (100-00 General Information, Description and Operation)...

    Other information:

    Ford Escape 2020-2024 Service Manual: General Procedures - Locked Seatbelt Retractor Releasing


    Repair NOTE: If the seatbelt webbing does not extract from the seatbelt retractor from the stowed position, this may be due to a normal condition which happens when the seatbelt retracts at a high rate of speed. Follow these steps to release the seatbelt...

    Ford Escape 2020-2024 Service Manual: Removal and Installation - Rear Bumper Cover


    Special Tool(s) / General Equipment Interior Trim Remover Removal NOTE: Removal steps in this procedure may contain installation details. Remove the rear lamp assemblies. Refer to: Rear Lamp Assembly (417-01 Exterior Lighting, Removal and Installation)...

    Categories

    Fastening the Seatbelts

    Ford Escape. Fastening the Seatbelts

    Insert the belt tongue into the proper buckle, the buckle closest to the direction the tongue is coming from, until it engages.

    read more

    Copyright © 2024 www.fordescape4.com